Search

In this paper, we propose a double balanced mixer with a tunable Marchand balun. The circuit is designed in a SiGe BiCMOS process using Schottky diodes. The tunability of the Marchand balun is used to enhance critical parameters for double balanced mixers. The local oscillator-IF isolation can be changed from –51 to –60.5 dB by tuning. Similarly, the IIP2can be improved from 41.3 to 48.7 dBm at 11 GHz, while the input referred 1-dB compression point is kept constant at 8 dBm. The tuning have no influence on conversion loss, which remains at 8.8 dB at a LO power level of 11 dBm at the center frequency of 11 GHz. The mixer has a 3 dB bandwidth from 8 to 13 GHz, covering the entire X-band. The full mixer has a size of 2050 μm × 1000 μm.

In this paper, a passive double-balanced mixer in SiGe HBT technology is presented. Owing to lack of suitable passive mixing elements in the technology, the mixing elements are formed by diode-connected HBTs. The mixer uses lumped element Marchand baluns on both the local oscillator (LO) and the radio frequency (RF) port. A break out of the Marchand balun is measured. This demonstrates good phase and magnitude match of 0.7° and 0.11 dB, respectively. The Marchand baluns are broadband with a measured 3 dB bandwidth of 6.4 GHz, while still having a magnitude imbalance better than 0.4 dB and a phase imbalance better than 5°. Unfortunately with a rather high loss of 2.5 dB, mainly due to the low Q-factor of the inductors used. The mixer is optimized for use in doppler radars and is highly linear with a 1 dB compression point above 12 dBm IIP2of 66 dBm. The conversion gain at the center frequency of 8.5 GHz is −9.8 dB at an LO drive level of 15 dBm. The whole mixer is very broadband with 3 dB bandwidth from 7 to 12 GHz covering the entire X-band. The LO–IF, RF–IF, and RF–LO isolation is better than 46, 36, and 36 dB, respectively, in the entire band of operation.

In this paper, we present an X-band double-balanced mixer in SiGe BiCMOS technology. The mixer core consists of a LO Matched quad diode ring using diode-connected Heterojunction Bipolar Transistors (HBTs). The mixer is integrated with a low-noise, high-linearity active balun on the RF port and a miniaturized Marchand balun on the LO port. Experimental results shows a conversion gain of +4 dB at 10.5 GHz with an LO drive level of 15 dBm. The LO-IF and RF-IF isolation is better than 36 dB and 26 dB, respectively, in the entire band of operation. The input referred 1 dB compression point is better than −11 dBm. The IIP2 is +13 dBm at a supply voltage of 3 V and +16.5 dBm at a supply voltage of 6 V. The measured noise figure is found to be ∼6.5 dB at 10.5 GHz.

In this paper, we present flicker noise measurements of two X-band direct conversion mixers implemented in a SiGe:C BiCMOS technology. Both mixers use a ring structure with either Schottky diodes or diode-connected HBTs for double balanced operation. The mixers are packaged in a metal casing on an Arlon 25N substrate to shield the sensitive noise measurement. Conversion loss measurements of both mixers is performed both for on-wafer and packaged versions. The experimental results shows that the Schottky diode mixer exhibits a 1/f noise corner frequency of 250 kHz, while the diode connected HBT circuit demonstrates a 1/f noise corner frequency around 10 kHz.

Baluns are used to transform an unbalanced input signal into a balanced output signal. Baluns are essential components in many microwave circuits, e.g., balanced mixers, or other differential architectures. When the signal is received by the antenna, it is single ended, and thus need to be converted to a balanced signal to benefit from a differential system architecture. Being first in the receiver chain, having a passive balun, will degrade the noise figure significant, thus it is beneficial to have low noise amplifier, which behaves as a balun. For the receiver to have a large dynamic range this balun must also have good linearity, and a high compression point (D. Manstretta, IEEE JOURNAL OF SOLID-STATE CIRCUITS, 47, 2012, pp. 407–420).

A new type of Marchand balun is presented in this paper, which has the property of complex impedance transformation. To allow the Marchand balun to transform between arbitrary complex impedances, three reactances should be added to the circuit. A detailed analysis of the circuit gives the governing equations. To verify the theory, a design and electromagnetic simulation of a lumped element Marchand balun is made in a SiGe BiCMOS technology. The lumped element impementation is favorable because capacitors are placed where the additional reactances should be added. Thus it is possible to absorb a positive reactance by reducing a capacitor. At the design frequency of 10.5 GHz it matches 50Ω to 50 - j66Ω. It has an insertion loss of 5.1 dB, an input reflection of −20.8 dB, as well as phase and magnitude imbalance better than 0.2° and 0.12 dB, respectively.

In this letter, a novel modified Marchand balun configuration with tunable phase balance is analyzed and verified experimentally. It is proposed to add a shunt susceptance in between the two couplers of the Marchand balun. This allows for a change in the phase balance which, to first order, is linear with the susceptance, while the magnitude balance is kept constant. To verify the proposed configuration, a lumped element Marchand balun has been fabricated using a SiGe BiCMOS technology. The balun design is centered around 9.4 GHz, with an insertion loss of 6.0 dB. The phase difference between the output ports can be changed from 175.8° to 183 ° whereas the magnitude imbalance is kept almost constant at 0.3 dB. The balun performs well in the range from 7 to 11 GHz, where it is possible to tune the phase to exactly 180°.